Former Community Admin
•
5.7K Messages
Outdoor Camera Recording Every 3 Minutes on firmware update 1.18 and 1.20
We are seeing a resurgence in reports of users who are seeing sudden and repeated motion triggers, resulting in a new recording every 3 minutes, and eventually a rapid battery drain for their Wireless Outdoor Camera. These repeated triggers seem to be occurring both during the day, and when Night Vision is activated.
A similar issue was resolved on firmware update 1.10 (November 2022), but users are now seeing new cases after their Outdoor Camera updated to firmware 1.18 (September 2023).
Our engineering team has identified the issue, and a fix is IN PROGRESS. A new firmware update will be rolling out soon to address the issue.
In the meantime, it can help to adjust the following settings for your camera experiencing this issue:
- Change your camera’s motion detection setting to All Motion
- If you have Activity Zones set up, adjust them to also block off the zones around the image that your camera is detecting
- Turn your camera’s sensitivity down to Medium or Low
You can make the above settings changes to your Outdoor Camera in the SimpliSafe mobile app by navigating to Cameras on the bottom navigation bar > select the gear icon in the top right corner > select [your camera] > Motion Detection.
New to the Community? Get started by reading our Welcome Article and please be sure to review our Community Guidelines before posting.
Related Conversations
0
0
hddolginoff
7 Messages
In similar situations with other defective products users have joined together on a class-action.
0
0
wakarusan
3 Messages
I removed battery and hard booted my outdoor camera, and it is still showing motion every 3 minutes or so. What now? This didn’t happen until the last 2 or 3 days.
1
0
lance843
1.1K Messages
Just for kicks and giggles I'm wondering what the actual problem was, curious minds want to know lol
1
0
hddolginoff
7 Messages
I just ordered a Nest outdoor camera and will be putting my Simplisafe camera where it belongs ... in the trash.
0
0
hddolginoff
7 Messages
I just ordered a Nest outdoor camera and will be putting the Simplisafe camera where it belongs ... in the trash.
0
MWM
4 Messages
I was able to temporarily solve the issue a couple of weeks ago by resetting the camera and adding it back to my system. However, the same issue reemerged this week (notifications every 3 minutes as soon as the sun goes down). I also noticed another of my cameras, which had been working fine since I purchased it, beginning to do this sporadically and it has led to significant battery drain despite being connected to a solar panel.
Is Simplisafe actually doing something about this? The communication from the Simplisafe team has been less than reassuring. The fixes they suggest are temporary solutions at best and any other competent technology company would have already released an update to address the problem by now.
1
0
castiscoular
2 Messages
I just wanted to pop in to say this is still happening to us. Our camera is on v1.18.23.5603... I just replaced the battery and it's nonstop. Our other outdoor cam doesn't do this. I've already tried fully resetting the camera and re-provisioning it but it's still happening. Please help?
1
0
karennik
1 Message
My outdoor cameras (2) continue to record and notify every minute with nothing to trigger them. We’ve tried blocking certain areas we think might be triggering and nothing. Alarms continue. This drains the battery 3 times faster than expected. Is there any update to program changes on stopping the recordings? Or is there something g we could be doing differently???
1
0
TheDudeWill
2 Messages
Hello, i recently got a simplisafe canera system for my home, and 1 of my outdoor cameras keep triggering its motion detection at night until the battery runs out. The camera is on 1.20.32.7392 update.
I have already tried turning the motion sesitivity down to low and there are no trees or bushes that coukd move in the wind. I think it might just be picking up shadows but im not sure.
Any suggestions?
2
0
ashma
2 Messages
Hello, there must be a fix date Simplisafe are targeting in their work tracking tool - what is it?
0
0
wellthereitis
10 Messages
LMAO, read other posts, Simplisafe is simply stating they are aware of the problem and are investigating it. Here's my analysis, lack of code control and reintroduced a problem previously resolved. When the same issue keeps recurring, it's usually code re-use, even when the code has been established to have a bug and code control would have prevented that code reuse.
As the meme states "Convince Me Otherwise".
0
Willj92
1 Message
I am having this issue on my front door camera at night time. I have tried the blind zones, turning the sensitivity to low as well as toggling from people only to all activity. None of these fixed my issue.
I see that the engineers are working on a fix, but this thread goes back several months. Does anyone know when this will be taken care of by an update?
3
rhallman
16 Messages
For me, the issue is continuing to get worse. At times there are multiple false alerts every few minutes. Settings are people only and set to medium sensitivity. All road traffic is blocked and when reviewing recordings, usually, all appear still.
0
0
adamjmcpilot
1 Message
We are experiencing the same “death loop” issue. Sad that this has been going on for months and Simplisafe still has not found a fix.
1
0
panteralee99
12 Messages
My cams have gone from 1.18 to FW 1.20.37.8185 as of a couple days ago and are continuing to not exhibit the every 3 minute false alarms. So far, things are stable. Last time they went from 1.18 to 1.20, one can had a meltdown. So far, so good.
0