‎Solar panel not charging | SimpliSafe Support Home
 

17 Messages

Tuesday, August 30th, 2022 7:57 PM

Solar panel not charging

I’m on my second panel and they don’t seem to be charging the camera. The only thing I haven’t tested is unplugging from the solar panel end which seems like a bad idea:

  1. Secure the connection between the Solar Panel's power cord and Camera by unplugging and reinserting both ends of the cable—the end connected to the Solar Panel and the end connected to the camera

Can you really pull the cable from the end connected to the solar panel? It feels pretty secure.

Official Response

Community Admin

 • 

5.7K Messages

2 years ago

Hi @3373inLine ,

You are correct, the Solar Panel's power cable is indeed not removable from the unit itself. Please don't attempt to try and pry it off!

As for the original issue - have you already tried doing a firmware reset on the camera? You can do so by pressing and holding the pairing button on the back of the camera for 16 seconds. When you release, it should reboot into setup mode, and you can set it up again through the SimpliSafe app.

If the issue is with the firmware or programming of the camera, that might resolve it.

17 Messages

@davey_d​ Thanks, Davey! I updated just now, but still not getting a clear indication (or charging icon within the battery icon) to tell me that the solar panel is working and charging the battery.


However, yesterday when I posted this I’m pretty sure the battery was at 95% and an hour later I saw the batter was at 97%. So I think it is working, but I don’t know definitively, which is a bummer.

Community Admin

 • 

5.7K Messages

Hm, yes. You should be seeing the charging icon when the unit is actively charging - could it be possible that it just wasn't at the time that you checked? But at least you're able to check that the charge is going up.

17 Messages

Hi Davey, on Friday I moved my solar panel to a sunnier location. Since then it has started to get at least six hours of sun. However there is no charging icon appearing in the camera settings in the app or on the website. And it does not appear to be charging from what I can tell, or it is just losing its charge at a much slower rate but not charging back up. It leads me to believe that either the solar panel is faulty or the charging port on the camera is faulty. It would be saddening that the solar panel is faulty as this is solar panel number two and I was having the same issue with the first one. What do you think?

6 Messages

@3373inLine​ I know this is off topic of the post here but how did you install that on your vinyl siding? I'm concerned the the supplied screws/anchor with the unit won't support the weight. Thanks in advance!

17 Messages

@davey_d Just an update: I am now seeing the charging icon finally. I recharged the battery to 100% and now it’s happening. Not sure why it wasn’t happening before. But good news!

5 Messages

2 years ago

As FYI, I have been having a similar outdoor charge issue via solar panel. The solar panel just does not keep up. I have attempted to have a settings profile that tries to minimize the use, but still having issues. I have no firmware updates, the panel location is in the sun, the cables are well seated. Also, the solar panel is about 18 months old and wonder if there is a failure rate? 

17 Messages

@mikemalloy0​ I found, if helpful, that I had to make sure the battery was 100% when plugging in. Once I did that it charged normally and keeps up. 

honestly I doubted that part at first, but now it works.

5 Messages

2 years ago

I am having an issue with four of these Simply Safe Solar panels.  I ditched 3rd party solar panels for these, but they atleast showed "charging icon" when the sun was up... What's with these not autorecognizing?

The camera has a computer chip, on it's power input, it's just sensing IV (current and Voltage) so whether it's a solar panel or a microusb wired to the wall outlet - they should recognize the solar instantly.

I work on large scale utility solar power plants, these are properly mounted (ok well not perfect.. kids running around the ladder, but sure should work) in the sun and I put in fresh batteries all properly charged too - what gives? 

Simplisafe brand name solar panels should be better than the 3rd party ones I'm now regretting throwing away too soon for these at 2x the cost.  The other ones didn't charge fast, but atleast showed the voltage icon of charging during rhe day.

I'll be pretty mad if I have to rebuy / reladder hang 3rd party panels and return $500 worth of 6x Simplisafe solar panels (I've hung 4x today) cause they don't have enough juice to even show charing on the cams like the 3rd party panels did even when cloudy. 

Dont' worry about the camera light shading part of the module on the right, it was early morning when I took these (sun at low angle)

(edited)

Community Admin

 • 

3.4K Messages

Hi @foremanjf​, 

Your Solar Panels seem to be mounted in a nice, sunny spot - they should certainly be charging your Outdoor Cameras.

Have you tried doing a firmware reset on your cameras? This can be done by pressing and holding the pairing button on the back of your cameras for 16 seconds. Once you release, they should each reboot into setup mode, and you can set them up again in the SimpliSafe app.

If you have already tried a firmware reset, I would secure the connection between your Solar Panels and Outdoor Cameras by unplugging and reinserting the cable connected to your Outdoor Cameras.

(edited)

5 Messages

@emily_s​ - I assure you all 4x solar panels have a.) proper micro USB connections made already double checked reading on advice above.  and b.) since the 3rd party solar panels were able to show charge lightning-icon... without a firmware reset... and since all 6x of my outdoor cams are running well on the Omada mesh network... I didn't see the reason to do be up on ladder firmware resetting all of these??  

I mean if the camera can detect the voltage of the 3rd party solar panels, without any firmware resets... Surely your own brand solar panel should do the same without issue?  I'd rather not waste an hour (back on the ladder) going doing that...

I mean the solar module IV detection is electronic, why would a firmware reset gate help (especially in light of the fact it auto-detected IV of 3rd party solar module just the week before).? Granted those showed a charging icon, but didn't seem to actually improve battery levels.

I love the simlisafe overall alarm system way more than Ring... but their solar panels work without issue and charge sufficiently.

I guess I can return all $500 of the 6x simplisafe solar panels to Amazon (I did like the aesthetics and type of mounting hardware more) but c'mon guys it's not me leaving all 4x loose micro USB connections (I get that it's the first troubleshooting tree they give you).

I really would rather keep the simplisafe panels for noted aesthetic/mount reasons, but if I go firmware reset all of these cameras... mount the last 2x solar panels for all 6x cams... and it still doesn't detect, you'll owe me first batch of the new improved (large enough, to push enough voltage, current) panels for so much ladder time (and it better use the SAME circle mount, so I'm not drilling more holes into the new home).  

The only saving grace is the hole-spacing of the Simplisafe circle 2-hole mount, is the same distance as the 3-hole mounts used on the Aluminum ball joint mounts via 3rd party solar panels... So I at least I'm not drilling extra useless holes into my new house facia.

Alright... I'll bite, I'll try the firmware reset - but you're talking to a long time solar industry professional (experienced PV module product manager/designer).  See note above, y'all owe me legit higher wattage brand name panels, that friggin autodetect IV, if I'm upon the ladder again these 6x still don't detect with charging icon after firmware resets too.  I mean a new improved model, not the same stuff.

(edited)

9 Messages

@emily_s​ Why are you saying to unplug and reinsert “both ends” of the cable? @davey_d wrote earlier in the thread that the cable doesn’t detach at the panel end.

Also, will Simplisafe correct the support page that has the same misinformation ?

(edited)

Community Admin

 • 

3.4K Messages

Hi @ewilen​, 

Thank you for calling my error out! I was looking at conflicting resources when writing my response. Davey is correct, the cable that is connected to the Solar Panel cannot be unplugged. We're working on getting the page in our Help Center that says it can be unplugged corrected. 

2 Messages

@foremanjf​ Did this work for you? 

1 Message

1 year ago

I tried everything mentioned in the other posts....what worked for me was checking the connection with the charging plug, You really have to press hard on the plug.....the weatherproofing makes it hard to get a good connection.

I also did a hard reset on my iPhone, just in case that was affecting the Simplisafe app.

2 Messages

thanks for typing this. i was SURE mine was plugged in correctly but after reading your reply, just to make sure, i unplugged and plugged it back in HARD and low and behold it started charging! so thank you again for calling that out!

1 Message

Wow!  Something so simple.  This did the trick for my issue.  I felt the ever so slight "snap" when the connector was seated correctly in the plug. Panels now charging!  Thanks.

(edited)

1 Message

I just tried your suggestion about pushing hard till you feel a snap, walla it worked, hope SimplySafe would include that in the simple installation instructions, I have 2 panels I didn't have to be so forceful when I plugged in my other panel. Your post saved me from further frustration,  thanks 

2 Messages

1 year ago

Does anyone have slightly cloudy days and their camera dies? How is someone supposed to keep their cameras charged in the winter when the sun is not always direct?!

1 Message

1 year ago

The app was telling me with the icons that my solar panel was working and charging the camera. But when I would arm and disarm my system, the home base would say the camera was low on battery. Well today the camera is disconnected and not working at all. Not sure how I would end up conflicting issues like this. I'm going to try and reset the camera and hopefully that will work. 

Community Admin

 • 

3.4K Messages

@OperJunge​ Yes, I would first try to reset the Outdoor Camera by pressing and holding on the pairing button on the back of the camera for 16 seconds to see if that resolves this.

When you said that the camera was disconnected today, was its battery dead? If it was, I would also charge the camera's battery for at least 5 hours using the charging cable that it came with. The Solar Panel is designed to keep the Outdoor Camera's battery charged, not charge it from 0 to 100, so fully charging the camera's battery before connecting it to the Solar Panel is recommended.

2 Messages

@emily_s​ I am also having this issue and have reset the camera, updated firmware, and checked that the connection to the panel is secure (and it definitely gets enough sun) and I am STILL not seeing a charging icon. My camera battery has gone from 100% to 96% in less than a day because I have a busy street so it is very disappointing that this isn’t working. Are there any other suggestions? I am outside of the return window for the panel.

Community Admin

 • 

3.4K Messages

@jlonchar​ If the Solar Panel isn't charging your camera despite taking all of these troubleshooting steps, there may be a hardware issue with the camera itself. If you contact our Support team, they can send you a replacement.

2 Messages

5 months ago

I am having the same issue. I have ordered another battery, thinking it was the battery, but I am getting the same issue!   I do not see a charge icon on my app, so the solar panel is not charging the battery.  Is there a warranty on this panel?  

5 Messages

Hey Brian,  just get these, mono c-Si solar PV modules with integrated Li-ion battery to charge the simplisafe cams.  I'm running 6x of these around house perimeter, cams are always charged now.  I never worry about the power now.  https://www.amazon.com/UYODM-Compatible-SimpliSafe-Wireless-continuously/dp/B09N716FJ3

2 Messages

5 months ago

My solar panel is not charging my camera properly.  I do not see the charging icon on my app.  I have also bought a new battery, thinking it could be that.  I have reset the camera multiple times as well.  Does this solar panel have a warranty? 

2 Messages

how hard have you tried plugging into the back of the camera? i had to push in quite a bit harder than i expected until it snapped in.

Community Admin

 • 

3.4K Messages

Hi @brianbryson​, 

As @raymondromero mentioned, I would unplug the Solar Panel from the Outdoor Camera and then plug it in again, making sure that it is flush to the camera. It may take a little force to plug the Solar Panel in all the way, so we recommend using both thumbs to push it in, if possible.

And just to confirm, is the Solar Panel pointed towards the sun and getting direct sunlight? If it is in a shady spot, that can prevent it from charging the Outdoor Camera successfully. I would also recommend wiping down the Solar Panel to ensure that it's clean and isn't getting obstructed by dust or debris. 

But if the Solar Panel is plugged into the camera all the way and it is getting sufficient sunlight, that could indicate an issue with the device itself. In that case, please reach out to our Support team and they can provide additional assistance. 

5 Messages

@brianbryson​ once you figure out you have plugged it in correctly, and its just a weak solar panel they sell - sadly giving a good camera a bad power experience... then just get these better PV modules with integrated battery to better always charge your simplisafe cam.

Honestly, simplisafe should pull their PV module design and relaunch the product matching this one that is superior - https://www.amazon.com/UYODM-Compatible-SimpliSafe-Wireless-continuously/dp/B09N716FJ3.  Been running 6x of these for 2 years now, cams are always powered up.

1 Message

5 months ago

I'm chiming in on the problem of a solar panel not charging my outdoor camera--and the problems of getting meaningful support. I'm hopeful other more knowledgeable SS support folks might have information to share, just as much as I hope community members might share information.

General Support Challenges

Extended email discussion with lots of photos ended up with a recommendation to call support. The phone support team tells me they have no access to either emailed or chat support—that's a big continuity problem in my opinion. That meant I had to start from scratch by phone with a conversation a few weeks old. The anonymous email author replied, "Again, we really apologize for what happened to your account. We will improve and develop our systems and services to ensure that this issue will not occur again."

My solar panel has not yet worked.

Is it charging?

I cannot tell whether the panel is charging my camera. Davey says in a reply somewhere in help discussions that we'll know through the app whether the camera is charging from the panel. The minimalist paper leaflet instruction card that came with the panel should have illustrated such icons. If there's wording in the app that the panel is working, then that should be illustrated, too. I can tell when my iPhone is charging through an icon with a lightning bolt; the color of the icon; an audible sound that it's charging; and haptic feedback. There are many references to all of these signals in Apple's documentation. Ring products that I routinely install (I'm an IT guy certified as a Pro to install these) all give indication when solar is connected, and when solar is charging (those are not the same thing.)

Cable attached?

I've made sure the cable is firmly in place, another apparently common issue with charging. It makes sense that weather-tight cables need to have firm connections. That same paper leaflet instruction card should have made that more clear. That wasn't my issue, either.

Firmware

We're told to make sure firmware is up to date, and that updates are automatic. (Well, then I should not have to worry about firmware updates, one would think.) I asked why there's no table online at SS support that shows what the current firmware should be for each of the 9 devices I have installed here. I should be able to look at my app and compare my installed products to a table of all SS devices to see if everything is up to date. Email support had no comment about this.

Reset firmware - remove/restore device

Then I did what I didn't want to do, to force a reset of firmware by removing my camera from my system and adding it back. That's a hassle of time to set up and customize again. Often, (Apple) wants us to completely wipe devices whenever there's a problem. It's simpler and faster **for support people** to tell consumers to do this—it's always great to start from a factory reset. Except that the time burden is extraordinary for consumers to put those devices  back how they once were. I mentioned to the email support staff about this point, and asked why there isn't a way to export camera settings out somewhere so that they can be restored later. No response. It's not clear when I do a firmware reset if fresh firmware is downloaded to the device through the base station during this procedure...or if simply the settings I had are removed. In any case, removing/re-adding the device back did not fix my problem.

<My phone conversation with Dale has now been dropped twice—the first time he called back; the second he did not. Dropped calls with SS support is not rare or unique in my experience--which is why I wanted to resolve this via email.>

Better product information before purchase

I learned the following from phone rep Dale today, information which would have been much more timely prior to purchasing a solar panel.

1) Solar panel maintains, doesn't "charge"

The panel will never charge the camera above the present level of charge on a battery. I incorrectly assumed this solar panel would behave like Ring or Nest panels with their similar products. Specifically, I expected the panels would eventually maintain **and** replenish a battery over time. I didn't especially care over how much time. So what happens when I use a battery starting with (in my case) ~60% charge? Dale said I need to charge the battery for 5 hours. But that's not a percent battery charge. My battery charge status is not measured in hours. It's measured in percent. Maybe it's a misnomer to call this a "solar charging panel" and instead a "solar charge maintenance panel."

2) Product placement

SS ads state the solar panels need only three hours of direct sunlight to maintain a charge. There's no statement about indirect sun, cloudy days, etc.  Dale explains that the panel must be angled up toward the sun. Apparently, anyone who hopes to mount a panel on a north exposure is in for disappointment and product failure.

I live in a condominium and am not allowed to attach anything to the building. I'm not allowed to deface the facade in any way. My condo faces west. I zip-tied my camera to a column facing south, not prominently west-facing on the facade; and angled the surface westward, but not upward. (The more I call attention to the panel, the more likely management will find a reason to make me pull it down and fine me for violations.) The panel sees indirect sunlight, because of its angle, from about noon-6PM.

3) Learning by example is preferable

My two-sided paper leaflet is simply not enough information for a product with this many variables and nuances. I get that it's too expensive to include much printed material at all. That's what online reference manuals, PDFs, bullets are all about.

I asked Dale to point me to support photo examples of successful solar panel installations. During the call, as when I initially wanted to purchase the panel, it's not an intuitive process simply to find the solar panel starting from ww.simplisafe.com. Dale sent me this link:

https://support.simplisafe.com/articles/outdoor-camera/wireless-outdoor-...

There are exactly two close-up photos, each with "textbook perfect" installations--but with little indication of context of a bigger picture. By virtue of shadows shown, images depict solar panels prominently displayed on south-facing eaves. This suggests that the panels installed as shown receive 100% direct sunlight, sun-up to sundown. Great! But for the rest of us not in a laboratory setup, I'd love to see photos of how others have done their installations. Googling such images shows me many aesthetically unacceptable solutions. By unacceptable, I mean affixing an unsightly ~3' long wood plaque to an exterior brick wall, to which solar panels are attached. Homeowners who don't care about the appearance of their structure can do that. In condominiums, owners do not own the brick walls, patio fence railings, columns. We're prohibited from hanging anything or permanently attaching anything (flower boxes, flag poles, bird feeders, decorations, signs). I welcome posts and suggestions from others homeowners who have conquered these challenges.

Unrelated battery problem

I had asked email support (and phone rep Dale today) how to resolve a problem with the second battery for my outdoor cam. I purchased two with my original system in 2021, knowing that I'd always need one battery charging while the other was in use. I provided a picture of the battery, whose plastic flat pin in the middle of the female receptacle was malformed if not broken. I cannot charge it; it's depleted and the camera does not recognize it. Dale was ostensibly investigating the matter when the call dropped; he never called back—and I'm now annoyed enough to write all of this out here. This problem is unresolved.

SimpliSafe app notifications

I had asked email support why the SS app always, everyday, has the "red ball 1" attached to its icon. In iOS, this universally means notification or alert to a problem requiring resolution. I faithfully tap the app and authenticate. No clue what the alert is, but the red ball goes away. I asked the team whether this is tied to the almost daily marketing prompt in my app to buy more hardware, or refer friends to SS; or if this is about a battery problem on my patio cam; or if this related to the expected text messages I get whenever we come and go. I asked for clarification so that I could adjust my notification settings in case I'm asking for duplicate notifications; or so that I could opt out of marketing when I thought I had already done that. I provided screenshots. I received no answer to that.

I really want to love my SS installation. It has potential. The monitoring is fine for my needs...and it's **not** the stalwart ADT thing.

Brian

07.21.2024

1.4K Messages

@briansean​ 

Try chat, might send you a battery, be very persistent and insistant, but professional and courteous.

Try webapp.simplisafe.com on a PC or in you're case a Mac or whatever for online battery status.

I do not use it and cannot vouch for whats there, if anything.

The Android app hasn't been close to responsive for battery feedback since camera firmware version 1.20 performance mode, base firmware then, don't remember.

Some of my 5 report full, take 5 refreshes to get any change, when not charging are blue or when 100 percent, when charging, black with a itty bitty tiny lightening bolt in battery symbol center. Unreliable overall for quite some time.

One never reports full, gets sun for 8-10 hours.

Power cables are NOT an option for me. Besides I spent $400-$450 on solar panels.

My tech caller has abandoned me with trying to fix mine, 15+ month since purchase.

They can't be fixed. They are now where they will "probably always be as to function. Which is inadequate for security for me. Other than detections, which is a long story overall. I have backup, other brands.

If you also upload some photos, I'd be willing to suggest what I can for placement and attachment options.

Mine are mounted on wood, house is all brick. We own it, so no rules except my own.

In winter because of sun angle, I have to babysit charge, turn cameras off, etc., as angle and degree of sun changes in winter.

Questions if any, ask.

I won't be on here much longer as I've about had it with Simplisafe personally.

New to the Community? Get started by reading our Welcome Article and please be sure to review our Community Guidelines before posting.