‎Updating Your Smart Lock | SimpliSafe Support Home
Skip to main content

Updating Your Smart Lock

Updated 

14 hours ago

Your Smart Lock receives periodic updates to ensure it’s always ready to protect your home. It’s important to download and install the updates as they become available to ensure that your Smart Lock receives any patches, fixes, and security updates.

Updating Your System

Before updating your Smart Lock, you’ll want to make sure that your system is running the latest firmware version. You can check for updates using the SimpliSafe® Mobile App. If your system is up to date, please proceed to the next section titled “Updating Your Smart Lock”.

  1. Open the SimpliSafe® Mobile App on your phone or tablet

  2. Choose My System from the bottom navigation bar

  3. Select Base Station Settings from the menu

  4. Next to Firmware, you’ll see Update Available if one is ready to install

    1. If you only see a firmware version, and no update is available proceed to the next section for ‘Updating Your Smart Lock’

  5. Tap on Update Available and follow the on-screen prompts to download and install the update

Updating Your Smart Lock

  1. Open the SimpliSafe® Mobile App on your phone or tablet

  2. On the Overview tab, there should be a tile that reads “Update Available”

  3. Then, choose Update Now

    1. You’ll need to make sure that Bluetooth is enabled on your phone or tablet - otherwise the update will fail!

  4. Bring your phone within 3 feet of your Smart Lock and wait for it to connect

  5. The Smart Lock will begin to update

    1. This may take up to 10 minutes to complete, so keep your phone nearby!

  6. Once the update is complete, you’ll receive a notice on your phone/tablet

  7. Finally, calibrate your Smart Lock

    1. Navigate to My System

    2. Choose Device Settings

    3. Select your Smart Lock

    4. Choose Calibration

    5. Tap on Begin to get started

Troubleshooting Smart Lock Updates

If the Smart Lock fails to update, there may be two main reasons for this. The first is that your Base Station or Keypad firmware are out of date. Please ensure that you check for updates for your Base Station and Keypad before running the Smart Lock firmware update.

You can check the Base Station firmware version by going to My System > Base Station Settings > Firmware.

You can check the Keypad firmware version by going to Menu > Enter Master PIN > System Settings > Diagnostics.

You’ll need to check each Keypad for the firmware versions within your home. If any of the  Keypad firmware versions are below 2.5, please contact our support team for additional assistance. 

If the update continues to fail, it’s possible that another device may be paired to your phone/tablet using Bluetooth which is causing interference. 

  1. Force quit the SimpliSafe® Mobile App on your phone or tablet (steps may vary depending on your device)

  2. Within your phone’s settings, ensure that Bleutooth is turned on

  3. Toggle Bluetooth OFF, wait about 10 seconds, then toggle it back ON

  4. Disconnect all other Bluetooth devices from your phone

    1. Wireless headphones, baby monitors, wireless speakers, car stereo, etc. are some examples of what may be active

  5. Open the SimpliSafe® Mobile App again on your phone/tablet

  6. Move your phone next to the Smart Lock and begin the update again

For best results, you must be within 3 feet of the Smart Lock

In some cases, your phone may enter power saving modes automatically if the battery drops below 30%. Please charge your phone above 30%, exit any power saving features that are enabled, and attempt the update again.

To rule out any device issues, we recommend trying to update the Smart Lock with a different phone or tablet as a next step. This can rule out the above, such as Bluetooth or battery issues, and help to identify any other misconfigurations on the device where the update keeps failing.

If the above does not work, we recommend power cycling the Smart Lock as a final step. Open the battery compartment on the back of the Smart Lock by applying even pressure upward (for Smart Lock Series 1) or to the right (for Smart Lock Series 2). Remove one battery for 30 seconds, then reinstall it into the lock.

Once the lock has been reset by power cycling it, recalibrate it by using the SimpliSafe® Mobile App or the Keypad.

SimpliSafe® Mobile App:

  1. Go to My System on the bottom navigation bar

  2. Select Device Settings

  3. Choose your Smart Lock from under the Door Lock category

  4. Tap on Calibration, then Begin to get started

Keypad:

  1. Select Menu

  2. Enter your Master PIN

  3. Use the arrows on the screen to select Devices

  4. Press right for Lock

  5. Then choose Recalibrate

Was this helpful?