How to Set Up a Replacement Base Station

Pick a Keypad from your system (if you have multiple) and slide off the backing plate to reveal the battery compartment. Remove a single battery to power down the Keypad.

Before proceeding to step 4, you’ll need to reset these specific devices (if you have any associated with your current system):

• Motion Sensor Gen 2: Remove the battery to reset

• Smart Locks (Original and Series 2): Remove the battery plate on the Smart Lock, then press and hold down the pairing button on the lock until all three lights begin to flash at the same time.

• Outdoor Cameras: Hold the pairing button on the back of the camera for 30 seconds. The camera should chime and begin to blink white. The chime indicates a successful reset. 

• Smart Alarm Indoor Camera: Press and hold the pairing button (the larger button) on the top of the camera for about 30 seconds. The camera should chime and begin to blink white.

Unbox your new Base Station and power it on by plugging it into a working power outlet. Specifically, one that receives continuous power and is not linked to a light switch. Your Base Station will announce “Welcome to SimpliSafe®” which means you can proceed to step 5.

Replace the battery in the Keypad that you took the battery out of in step 2. The Base Station should announce “Keypad, Added” if it automatically connects.

If your Keypad does not automatically connect, you’ll need to use an alternative pairing method to get connected again.

If your Keypad Does Not Automatically Connect, use this Alternate Method for Pairing:

1. Unplug your Base Station’s power cord from the bottom of the Base Station. Then, use a Phillips head screwdriver to remove the screw.

2. Untwist the cover from the Base Station, but leave the batteries in place to keep it powered on.

3. Locate the “Emergency Pairing Button” on the bottom of the Base Station, opposite of the power cord port. You’ll press this in step 5.

   

4. Power cycle the Keypad by fully removing a single battery and reinserting it.

5. As soon as the Keypad screen says “Searching for Base Station”, press and release the “Emergency Pairing Button” on the bottom of the Base Station.

6. The Base Station will announce, “Keypad, added” if successful.

When prompted by the Keypad, input a Master PIN. This can be the same PIN you used before, or a new one. Then, use the Keypad to connect your Base Station to your location’s Wi-Fi (opens in new tab) network. The Keypad uses ABC mode for typing on it (opens in new tab), which is similar to how you may have typed on an older cellphone using T9.

Once you have connected the Base Station to Wi-Fi, you’ll need to complete the transfer within the SimpliSafe® Mobile App.

To Replace Your Base Station Using the SimpliSafe® Mobile App:

1. Open the SimpliSafe® Mobile App on your phone or tablet

2. If you have multiple locations, ensure you are on the correct one before proceeding

3. Choose My System from the bottom navigation bar

4. Tap on Base Station Settings

5. Scroll down to the bottom and choose Replace Base Station

6. Follow the in-app prompts to complete the process

If you receive an “Invalid Base Station Serial Number” error message (opens in new tab) during this process, it could mean that you’re missing account information. You will need to confirm your monitoring address in the Online Account (opens in new tab) first, then try again.

Once the new Base Station is connected to your SimpliSafe® account, you can proceed with setting up the rest of your products. You will need to add back all products from your previous system, including the ones you reset in earlier steps.

To add a Product to your System:

1. Open the SimpliSafe® Mobile App (opens in new tab) on your phone or tablet.

2. Tap on the three-bar menu (hamburger menu) in the upper left corner of the screen.

3. Choose “Add Device or Camera (opens in new tab)” from the list of menu options.

4. Select Get Started, then follow the in-app prompts to choose your product and add it to your system.

When your Base Station was replaced, its system and device settings were reset. You’ll want to go through your menus under the My System tab for Base Station Settings (opens in new tab), Device Settings, and/or Camera Settings and make sure that each device is set back up to your specifications.