Smart Lock Series 2 Overview and Installation Guide

Confirm Your Existing Door’s Lock is Compatible

Before installing the Smart Lock, you will need to ensure that the lock on your door is compatible. 

The Smart Lock only works with single cylinder deadbolts. These deadbolts have a thumbturn on the inside of the door and a keyhole on the outside. Other requirements include:

• A clean, unobstructed strike plate and borehole

• Screws that are installed horizontally 

Add the Smart Lock in the SimpliSafe® Mobile App

1. Open the SimpliSafe® Mobile App on your smartphone or tablet

2. Navigate to the three-bar menu on the upper left corner and select Add Device or Camera

3. Select Smart Lock from the list of available products

Pair the Smart Lock to Your System

1. Remove the battery cover on the Smart Lock by applying pressure to the front of the lock and sliding the cover to the right

2. Press and release the setup button located above the Smart Lock’s batteries 

3. Choose a name for the device by selecting one of our pre-populated names, or select Custom Name at the bottom of the screen to input your own

Prepare Your Door

1. On the outside of your door, place a strip of painter’s tape over the deadbolt to keep it in place

2. On the inside of your door, unscrew the deadbolt’s thumb turn and save the screws for a future step

Install the Mounting Plate to the Door

1. The mounting plate for the Smart Lock is located on the back of the lock, tucked in with the Smart Lock’s wing latches

2. Using the included release tool, slide the wing latches out on both sides of the Smart Lock

3. Remove the mounting plate from the Smart Lock

4. Place the side of the mounting plate that says “This Side to Door” on your door

5. Align the central bottom hole of the mounting plate around the tailpiece of the door’s lock

6. Using the screws that were removed from the deadbolt’s thumb turn, secure the mounting plate into place - making sure that you don’t over-tighten the screws as this can bend the mounting plate

   1. If the screw heads are not wide or strong enough to support the mounting plate, use the included washers

Attach the Tailpiece Adapter

1. In the Smart Lock’s box, you will find 4 colorful tailpiece adapters to place on the deadbolt’s tailpiece

2. Try placing each adapter on the deadbolt’s tailpiece until you find the one that fits naturally. Do not force the adapter to fit the tailpiece

3. Unlock your door

4. Locate the notch on the tailpiece adapter—this is a small, raised bump

5. Slide the adapter on the tailpiece so that the notch is facing toward the hinges of the door

Mount the Smart Lock to the Door

1. Unlock the Smart Lock by turning its thumbpiece

2. Slide open the wing latches on the back of the Smart Lock using either your hands or the release tool

3. Slide the Smart Lock over the adapter, slowly turning the thumbturn until it aligns and slides snug to the mounting plate

4. Push the wing latches back into the Smart Lock so they clamp on to the mounting plate

   1. You’ll know the Smart Lock is successfully seated when it is not loose and sits flush against the door

5. Turn the thumbturn to confirm it moves smoothly into both the locked and unlocked positions and there are no obstructions

Install the PIN Pad

1. Remove the battery tab from the PIN Pad to pair it with the Smart Lock

2. Use the double-sided adhesive or included screws to mount the PIN Pad to the outside of the door, ensuring that there’s at least 3 inches of space underneath the PIN Pad so you can access its batteries

Calibrating the Smart Lock

Once you have completed installing your Smart Lock and PIN Pad, return to the SimpliSafe® Mobile App. In the App, you’ll finish the setup and go through a calibration process for your Smart Lock.

If the calibration fails, please refer to the Troubleshooting Smart Lock Calibration article for further assistance.

Testing the Smart Lock

Once the Smart Lock is calibrated, you may test your PIN Pad by entering your Master PIN or a Custom PIN to unlock your door. Entering your PINs on the PIN Pad will also disarm your system when unlocking your door.

Sync an Entry Sensor With the Smart Lock

If you have an Entry Sensor on the same door as your Smart Lock, you may sync the two together to prevent the Smart Lock from locking when the door is open. To do this, simply press the setup button on the Entry Sensor when prompted in the SimpliSafe® Mobile App.